lconia B1-a71 root 方法

那個說明檔並沒有說明如何安裝~
只告訴我們可以怎樣設定USB的讀取方式!
到頭來一樣驅動程式沒辦法安裝，但照理說是不必安裝了！
因為平板在第一次連接電腦時就會自動安裝了！
不然是絕對讀不到平板的，但已經確定讀的到平板
但程式卻讀不到，可能是電腦問題也可能是程式的BUG！

大致上就是在按１然後Enter再按一次Enter就會冒出"請確定USB調式以開起並以連接至電腦"

這真的可以成功ROOT嗎....
板上還有其他成功的網友嗎
怎麼感覺只有原PO成功....
搞了一個禮拜了還是無限重開....

葉子~飄飄 發表於 2013-5-18 12:14

                               
登錄/註冊後可看大圖

那個說明檔並沒有說明如何安裝~
只告訴我們可以怎樣設定USB的讀取方式!
到頭來一樣驅動程式沒辦法安裝，但 ...

那個說明檔告訴你如何切換模式
切換後就執行SETUP安裝即可

philajaj 發表於 2013-5-18 13:07

                               
登錄/註冊後可看大圖

這真的可以成功ROOT嗎....
板上還有其他成功的網友嗎
怎麼感覺只有原PO成功....

筆者只能說
有人成功有人失敗

======= Acer Iconia B1-A71 Toolkit v0.5.5 =======

What do you want to do?
[1] Root
[2] Unroot
[3] Internal 2 External (only with root!)
[Q] Quit

Enter a selection: 1

================== Root =================
Before we can start, please do following:
1. Make sure drivers for Acer Iconia B1 are installed, you can find them here: h
ttp://goo.gl/doR8L
2. Plug-In your Acer Iconia B1 into this PC.
3. Enable USB Debugging Mode by going into Settings -> Developer Tools.
4. Put prerooted system.img.gz into folder: system_image.
5. Keep your device plugged in until it's finally rooted, or this procedure is a
borted!

If you sucessfully applied the steps above, we can now start.
You can always abort by pressing Ctrl+C


[ENTER] Continue
[Q]     Quit

Enter a selection:

Trying to establish ADB Connection...
E：Couldn' t connct to Acer Iconia B1-A71 over adb. Plug-In device with USB-
Debugging Mode turned on.
Check if drivers are properly installed.

If  you keep getting this error, try to run toolkit with -d or --debug parameter
Press Enter to leave Application...

驅動程式安裝成功了，但依然如此...

======= Acer Iconia B1-A71 Toolkit v0.5.5 =======

What do you want to do?
[1] Root
[2] Unroot
[3] Internal 2 External (only with root!)
[Q] Quit

Enter a selection: 1

================== Root =================
Before we can start, please do following:
1. Make sure drivers for Acer Iconia B1 are installed, you can find them here: h
ttp://goo.gl/doR8L
2. Plug-In your Acer Iconia B1 into this PC.
3. Enable USB Debugging Mode by going into Settings -> Developer Tools.
4. Put prerooted system.img.gz into folder: system_image.
5. Keep your device plugged in until it's finally rooted, or this procedure is a
borted!

If you sucessfully applied the steps above, we can now start.
You can always abort by pressing Ctrl+C


[ENTER] Continue
[Q]     Quit

Enter a selection:

Trying to establish ADB Connection...
E：Couldn' t connct to Acer Iconia B1-A71 over adb. Plug-In device with USB-
Debugging Mode turned on.
Check if drivers are properly installed.

If  you keep getting this error, try to run toolkit with -d or --debug parameter
Press Enter to leave Application...

驅動程式安裝成功了，但依然如此...

現在插著平板一運行就跳掉，拔掉就說沒連接～
難道我的電腦不能用嗎?

求救啊...驅動安裝完後成是一運行就跳出...
搞啥，好不容易安裝好驅動，結果第一個繼續按下續跑一下就退出！
冏爆了啦

現在終於跑的動了...但到輸入指令那一步又...
他輸入完會自動按RUN，但按下去程式就跳掉了...
所以還是沒成功 =  ="

不知道為何一直這樣子 跟上面大大一樣問題 偵錯開了 驅動裝了
此題還是無法解決=ˇ=

小弟找很久終於在這邊找到了
謝謝分享