120578327_2633103713666757_208309135276399325_o.jpg (528.69 KB, 下載次數: 2)
2020-10-13 08:23 上傳
DIYer like me, decided to replace the broken LCD screen module during the last holiday of the Moon Festival.
120735372_2633105900333205_3202928064279700461_o.jpg (330.18 KB, 下載次數: 3)
2020-10-13 08:26 上傳
Always take photos before operation.
The new LCD display module has both one connector and one socket that link to Nokia 5 motherboard, this is the video connector.
120580509_2633105976999864_4874949667109097583_o.jpg (363.27 KB, 下載次數: 3)
2020-10-13 09:10 上傳
Using enlarging function of camera can let you examine more carefully on key parts on the new LCD display module.
The other socket is responsible for data transmission of return/menu/home touching areas in front of Nokia 5.
120611263_2633106080333187_2720767596524674532_o.jpg (366.87 KB, 下載次數: 2)
2020-10-13 08:28 上傳
For every craftsman, using proper tools can avoid damaging parts.
I sharpened the tip of the small plastic shovel before operation so that it is easily to flip the gate of connector to insert/pull out the data cable attached to this connector
120596371_2633106386999823_2878366572772787367_o.jpg (472.61 KB, 下載次數: 2)
2020-10-13 08:29 上傳
Using hairdryer instead of professional heating tools is O.K.
The glue will get soft and easily removed, especially the top and the bottom of front panel.
120780038_2633106416999820_4118375015291270141_o.jpg (430.17 KB, 下載次數: 2)
2020-10-13 08:30 上傳
Focus on heating only the edge of LCD screen, since the broken glass is fragile, it was easy to remove the glue.
120507366_2633106466999815_1731289014422513867_o.jpg (400.97 KB, 下載次數: 2)
2020-10-13 08:31 上傳
Actually the glue has been harden at the edge, use knife carefully to peel the glass from the edge, cut it off while beware of the fragile glass! Protect your eyes!!
120592997_2633106536999808_1696680486116138422_o.jpg (445.68 KB, 下載次數: 2)
2020-10-13 08:32 上傳
Also can be done using any thin hard plastic sheet. Open the broken display panel from the top first.
120757305_2633106696999792_1229140793801549166_o.jpg (502.11 KB, 下載次數: 2)
2020-10-13 08:33 上傳
Watch out, here comes the LCD display connector and cable, don"t remove the broken screen off too quickly.
Using small screw driver to remove the screw.
120603715_2633106723666456_8803914755527531662_o.jpg (364.98 KB, 下載次數: 2)
2020-10-13 08:34 上傳
After removing the small iron plate, you will see the display connector.
120578556_2633106813666447_7423114625627596282_o.jpg (443.04 KB, 下載次數: 2)
2020-10-13 08:34 上傳
Lever up the connector from the top skillfully, it was only attached upon the surface of socket.
120601826_2633106890333106_8051277898550661506_o.jpg (369.21 KB, 下載次數: 4)
2020-10-13 08:35 上傳
The above was the old broken LCD display panel module, the motherboard and battery were behind the silver iron plate.
120617741_2633106956999766_6394069001806239129_o.jpg (405.96 KB, 下載次數: 2)
2020-10-13 08:36 上傳
Comparing these two modules, we still need to get the return/menu/home sensors from the old module.
120655346_2633106993666429_4079554183452850652_o.jpg (480.23 KB, 下載次數: 3)
2020-10-13 08:37 上傳
Checking the serial numbers of sensor and LCD screen, the latter is the same as the new LCD screen"s. Note the sensor later will be taken down and transplanted to the new module.
120601964_2633107066999755_4969791514196980470_o.jpg (381.71 KB, 下載次數: 2)
2020-10-13 08:38 上傳
Clearly the sensor will be placed upon to fill the hole and proper area showed as indicated.
120599426_2633107150333080_8072307735380736852_o.jpg (440.96 KB, 下載次數: 2)
2020-10-13 08:38 上傳
Remover the yellow sticker from the old module. The cable and connector of sensor was revealed.
120611936_2633107193666409_8898898532866825473_o.jpg (464.08 KB, 下載次數: 2)
2020-10-13 08:39 上傳
Again using small plastic shovel to lever up the small gate from the white part. Gently.
120631037_2633107230333072_834658029454578202_o.jpg (563.69 KB, 下載次數: 4)
2020-10-13 08:39 上傳
Pull out the cable, we have the sensor of return/menu/home.
120591845_2633107400333055_4857782998636122476_o.jpg (463.14 KB, 下載次數: 2)
2020-10-13 08:40 上傳
This is the front view.
Carefully remove the glue around the black glass button. And don"t erase the square white sensor when peel off the glass and glue.
120632573_2633107463666382_5899941358696795423_o.jpg (383.54 KB, 下載次數: 2)
2020-10-13 08:41 上傳
Ready to transplant the sensor upon the new LCD display module. Note, the gate of small socket has been open before.
120575292_2633107540333041_5248262807948342660_o.jpg (383.51 KB, 下載次數: 2)
2020-10-13 08:48 上傳
Put the cable inside the socket and close the gate of connector.
120614224_2633107613666367_6286351666856125402_o.jpg (350.61 KB, 下載次數: 2)
2020-10-13 08:49 上傳
Put back the yellow protection sticker upon the socket and connector.
120653983_2633107743666354_7897204426625021377_o.jpg (441.78 KB, 下載次數: 2)
2020-10-13 08:50 上傳
Now it"s time to clean the residual glue and tiny glass on the base before installing the LCD panel module.
Scratch any glue around the edge so that we may get a flat and nice outlooks.
120594054_2633107843666344_6611648860450396207_o.jpg (426.21 KB, 下載次數: 2)
2020-10-13 08:51 上傳
I put them in the wrong direction in the last picture, this is the right angle.
Note the cable can never be bend.
120599426_2633107986999663_4055239202533357421_o.jpg (321.54 KB, 下載次數: 4)
2020-10-13 08:52 上傳
Using finger to install the LCD display cable upon the socket on motherboard.
You will feel a click when in right position.
120572073_2633108023666326_2589010729944755214_o.jpg (317.36 KB, 下載次數: 2)
2020-10-13 08:52 上傳
Always testing before any glue operation.
Great! my Nokia 5 is coming back.
120599452_2633108076999654_3711679250123053772_o.jpg (268.7 KB, 下載次數: 2)
2020-10-13 08:53 上傳
The light on sensor to show "return/menu" also functioned well.
120597726_2633108146999647_2805844528668274342_o.jpg (402.32 KB, 下載次數: 3)
2020-10-13 08:53 上傳
Finally, I only used double-side tape instead of technical glue.
Oh, I should have pasted the tape upon the edge of motherboard instead of panel, damn me!
p.s You"d better use fast glue with fine dip tube to seal the panel and metal case, but beware of the power and volume buttons at the side. Don"t dip too much fast glue to fail the function.
120589030_2633108126999649_4015244083968761932_o.jpg (524.64 KB, 下載次數: 2)
2020-10-13 08:55 上傳
Behold the Nokia 5 and hTC E9 plus, both they are old models, they"ll accompany me till the next new model, maybe iPhone 12? Who knows?
Thanks for watching.
作者: philipchen01 時間: 2020-10-12 06:32
咦，不好意思，新手發文請多見諒。
自己佔個位先^^。
請教前輩，我使用桌上型電腦製作完將原本存於臉書中的圖檔位址複製過來貼於圖片網址，事後再使用電腦閱讀可以見到圖片無誤，但為何將網址貼於手機的LINE上，告知朋友用手機開啟連結閱讀時，是否就看不到圖片呢?
作者: philipchen01 時間: 2020-10-13 09:24
原來還是得將圖片上傳至本站的圖庫中再引用過來，謝謝管理員的指導。
已修正，行動裝置也能觀看得到圖片了。
| 歡迎光臨 Android 台灣中文網 (https://apk.tw/) | Powered by Discuz! X3.1 |