馬上加入Android 台灣中文網，立即免費下載應用遊戲。
您需要 登錄 才可以下載或查看，沒有帳號？註冊
x
本帖最後由 z1230401 於 2013-8-28 14:54 編輯
以下適用於有刷機經驗的人，本人及作者都不承擔後果。
若失敗無法開機只要重刷ROM就可以恢復了←個人經驗-_-
由國外Hashcode, Dhacker團隊所製作的內核，功能超頻，CPU，GPU的控制，UNDERVOLTUNG選項，RAM的調整等..
CPU設置為默認的1000 MHz最大←可調到1300 最低 100
預設就很省電了，當然你可以調的更省電但可能會導致你的手機不穩定如當機等~或者你也能調快一些但這樣是不省電的。
以下為原文介紹 我英文不好就不翻了@@
Battery Friend toggle (a battery friendly mode)
Dynamic Hotplug
Optimized OPP Table for smooth CPU scaling
Frequencies: 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1350
Modifed Smartreflex driver (Custom Sensor for detecting n-Value).
Smartreflex Tuning Interface: Set min calibrated voltage
Smartreflex Tuning Interface: Set max calibrated voltage
Overriden trim quirks (experimental port from OMAP4460, no DCC) to override factoy defaults and reach stable overclocking up to ~1,5ghz (depends on device, each silicon is different!)
Overclocking using Live OC (mine runs stable at a maximum frequency of 1,498ghz!)
New configuration for dvfs and emif
hwmod, uart - cleanups from pre-kexec config to safe power
hwmod, uart, IRQ - Configuration for power saving
Screen off governor is hotplug: Second core will be turned off ONLY while screen is off!
CPU: lower voltages for CORE and IVA. Give CORE the abbility to scale up to higher voltage if needed
Added IVA_NITROSB
CPU: Lower voltage limit for mpu SR_MAX
PM: IVA AUTO RET relaxed workaround in idle path
Intellidemand: No hotplugging while screen is on.
Dynamic fsync control
Dynamic page-writeback
Frandom v2
JRCU / Tiny RCU
Raised voltage limits for mpu a bit
Raised the temperature limits from 64c* to 74c* (degrees)
Net: Increased IPsec/TCP Up/Down Speed
optimized CRC32 algorithm (better code generation)
mm: Page writeback interval is dynamic depending on screen state.
Optimized LZO compression
fs: asynchronus I/O latency to solid-state disk
Net: Wireless: Removed a return rule to get rid of the rx_wake/wl_wake wakelocks
CPU: policy->min set to non-static 100mhz to avoid user to be stuck at 100mhz min. Sideeffect is that you have to set the frequency lock in trickster to force the CPU to stay on your preferred min frequency, otherwise it will always jump back to 300mhz - 1000mhz.
RW Readahead 1024
Watchdogs disabled
ARM: Allow arm_memblock_steal() to remove memory from any RAM region
Devices: Deeper idle states
Increased ducati heap size
zRAM support
GPU has 3 scaling steps and OC to 416mhz
GPU: Added C4 states for Power Down mode
GPU_OC: max 416 mhz
Multicore Power Saving Mode Control
ARCH Dependant Power feature
Temp Control (Modify temperature limit for CPU/MPU)
Gamma Control
Screen/Display: Modified OMAPDSS for sharpness and lightning colors
OMAPDSS: Added variable clock rate and OPP - allows the screen to scale down power and voltage
Fsync Control: LEss IO Speed but safes you from loosing data if phone crashes
Filesystem, Android Staging, lowmemkiller: Heavy modified for R/W Speed and efficient performance
Custom Voltage Support
IO: SIOPlus, Fifo, Row, VR, Noop, Deadline, CFQ
CPU: More Governors
Deep Idle
ARM Topology
Many improvements in overall OMAP PM
SELinux patched
GREAT performance!
GREAT battery life!
Support for Ezekeel\'s \"eXperience\" App (Adds features: Music Control with Vol-Buttons, etc..)
Support for Trickster Mod Kernel Control App (Download from Gplay)
需要第三方Rom (如CM, AOKP, AOSP) 。 澳版 官方版不能刷，若刷了會開不了機
需安裝bmm照一般刷rom方式刷入即可。
若之前有刷過其他特殊內核調整請移除
停用所有CPU調整
-----------------------------------------------------------------------
JBX-Kernel-1.0 FOR 4.3 ← 目前使用正常，不會像4.2.2開不了機。
http://d-h.st/TH5
JBX-Kernel-0.8.2 FOR 4.2.2 ← 我個人刷在4.2.2系統常常會開不了機 自行決定是否刷入 。
http://d-h.st/zTr
Trickster MOD 2.4 (頻率控制)
apk.tw_Trickster MOD.apk
(1.45 MB, 下載次數: 92)
|
評分
-
查看全部評分
|
鑽石
碎鑽
金豆
收藏
分享
專題
提升卡
變色卡
排首位
樓主
